How To Clean A Chainsaw

Is your chainsaw filthy?

Do you want it to sparkle like new again?

If so, this guide is for you. Below, I’ll teach you how to clean a chainsaw to look spotless and work like new again. No matter if your chainsaw is a complete mess or just a tad bit dirty, these same tips apply. Also check, How to repair one!

Steps for How to Clean a Chainsaw

Before you clean the different chainsaw types, you have to guarantee that there’s no force rushing to the instrument. Something else, a mishap could happen.

Before you play out any of the cleaning chainsaws underneath, make these arrangements:

• Gas Chainsaws — Drain the fuel tank and disconnect the spark plug connector from the spark plug.
• Battery Chainsaws — Remove the battery.
• Corded Electric Chainsaws — Detach the power cord.

Stage 1: Cleaning the Bar

Please find the two nuts on the chainsaw’s side cover that mount the guide bar to the powerhead; however, don’t release them right now.

On sure chainsaws, you can’t remove the cover while the chain brake is locked in. You may have the option to take the cover off on different models, yet putting it back gets troublesome. In this way, consistently separate the chain brake before beginning this undertaking.

After the chain brake is separated, loosen and remove the cover nuts.

Separate the guide bar and chain from the powerhead. Set the chain aside.

If the guide bar is modestly dirty, you can simply utilize a cleanser and water on a cloth to clean it. If it’s heavy y soiled, at that point, a degreaser dissolvable might be required to loosen the buildup of gunk.

Concerning cleaning the chainsaw direct bar groove, you can either use a unique groove cleaning tool or a putty knife. Run the tool around the groove until it’s free from any gunk between the rails.

To clean the bar and chain oiler openings (situated at the base of the bar), utilize a pick or thin screwdriver to separate any gunk blocking the holes. Packed air is additionally something worth being thankful for to use in these little spots. Your guide bar may likewise have an opening close to the tip of the blade for oiling the sprocket. Clean that out too.

Stage 2: Cleaning the Chain

In an all-around ventilated zone, take a container and mix one ammonia cup with one gallon of water.

Spot the chainsaw chain in this arrangement and let it soak for 15 minutes.

Put on a couple of thick elastic gloves for security. At that point, use a delicate bristled toothbrush to scrub each section of the chain until it’s free of debris.

When the chain is clean, rinse it under water to remove the ammonia solution. Immediately dry the chain after rinsing so that all of the moisture is removed.

Fill a shallow plate most of the way with bar and chain oil. Lower the chain in the oil and let it sit for three hours. After that time, turn the chain over and let it sit for an additional three hours.

Remove the chain from the plate and use paper towels to touch the chain to dispose of any dripping oil.

Also, check for How to replace chainsaw chains

Stage 3: Cleaning the Powerhead

Wipe the outside of the powerhead body with a dry fabric.

Utilize a delicate paintbrush (1 to 2″ wide) to clean off any dirt that has held up around the crankcase, grasp drum, and bare studs.

For thick gunk stuck in those regions, use a pick or thin screwdriver for scratching it out.

Stage 4: Cleaning the Air Filter (Gas Models Only)

Remove the top cover of the chainsaw.

Take the air to sift out and stuff the air intake with a cloth so that no dirt or debris falls into this area.

Use a soft paintbrush (1 to 2″ wide) to remove any collected dust on the air filter.

If the air channel is unnecessarily filthy, run it under water to remove any stuck particles. At that point, let it dry before reattaching.

Stage 5: Cleaning the Spark Plug (Gas Models Only)

With the top cover removed, you can access the spark plug.

Utilizing a T-Wrench or the provided Scrench with your chainsaw, unscrew, and remove the spark plug.

If the electrodes are a dark brown color, then it should be fine. If they’re black, chipped, or damaged looking, it’s time for a replacement.

Check your owner’s manual for the correct spark plug part number.

Stage 6: Cleaning the Cooling Fins (Gas Models Only)

Remove the sideboard that covers the cooling fins and rope rotor.

Utilize a slim screwdriver to daintily scratch out any gunk that is gathered between the cooling fins. Be tenderly here since you would prefer not to twist the fins.

Use a delicate paintbrush (1 to 2″wide) to remove any collected debris inside the rope rotor area.

Stage 7: Reassemble the Chainsaw

When you have finished the cleaning of your chainsaw, reassemble the parts in reverse order.

What’s Next?

Now that your chainsaw is clean from the inside out, you should notice an increase in performance.

Hopefully, this article has helped you understand a lot about the subject.